zNetLaB › Guided labs › Service Provider
Troubleshoot: VRP loopbacks reachable but not labelled
Service Provider Advanced 2 devices 1 checked tasks 100 points Plan lab
OSPF between the two AR routers is fine and the loopbacks ping, but there is no LDP LSP to the far loopback. You build it in a browser, type real commands at each device, and every task below is
checked against the running configuration — so you find out it is wrong before anybody else does.
Open this lab in the simulator
The simulator runs in your browser with nothing to install. This lab is part of the full simulator: open it free for 7 days with a new account, then with a plan. It needs an account, which keeps your progress.
The scenario
OSPF between the two AR routers is fine and the loopbacks ping, but there is no LDP LSP to the far loopback.
Your role: an engineer in the provider’s network operations centre. Level: Advanced Done when: all 1 goals show as passed (100 points).
Network status
Devices: 2 routers, cabled as drawn. No Layer 1 or Layer 2 faults: every link is connected and up. A, B start with an empty configuration.
Known problems
The network worked and now does not: the scenario above says what users report. The cause is a configuration fault, not a cable. Find it with show commands (interfaces, routes, neighbours, running-config) before you change anything; fix only what is wrong.
Goals
A has an LDP LSP to B loopback (100 pts)
The activity, in order
A has an LDP LSP to B loopback B has mpls on GigabitEthernet0/0/0 but no mpls ldp there. Add mpls ldp under the interface.Why: Each goal is a state the lab can check on the running device. Verify with: display mpls ldp lsp
Tips
Work in the order given: later goals depend on the earlier ones. After every change, run the verify command before moving on; do not guess. Stuck? Read the verify output first. It names the interface, neighbour or route that is wrong.
Why this matters
OSPF between the two AR routers is fine and the loopbacks ping, but there is no LDP LSP to the far loopback.
What you will be able to do
A has an LDP LSP to B loopback
The network
Huawei AR2220 — 2 devices in all, already cabled.
Gi0/0/0 Gi0/0/0 A B Drawn from this lab: devices, cables, ports and the addresses already set.
Device Model Address already set
A Huawei AR2220 configure it
B Huawei AR2220 configure it
Cabling
A Gi0/0/0 ↔ B Gi0/0/0
What is configured at the start
These are already configured when the lab opens — including, where this is a troubleshooting lab, the fault itself:
A system-view
interface LoopBack0
ip address 1.1.1.1 32
quit
mpls lsr-id 1.1.1.1
mpls
quit
mpls ldp
quit
interface GigabitEthernet0/0/0
ip address 10.1.0.1 24
mpls
mpls ldp
undo shutdown
quit
ospf 1
area 0
network 10.1.0.1 0.0.0.255
network 1.1.1.1 0.0.0.0
quit
quit
return
B system-view
interface LoopBack0
ip address 2.2.2.2 32
quit
mpls lsr-id 2.2.2.2
mpls
quit
mpls ldp
quit
interface GigabitEthernet0/0/0
ip address 10.1.0.2 24
mpls
undo shutdown
quit
ospf 1
area 0
network 10.1.0.2 0.0.0.255
network 2.2.2.2 0.0.0.0
quit
quit
return
Tasks, and how each one is checked
Every task is decided by reading the live network — a neighbour in FULL, a ping that succeeds, a line in the running configuration — not by looking for a keyword you typed. The same command shows you what the lab sees.
# Task Pts How to verify it yourself
1 A has an LDP LSP to B loopback 100 On A: display mpls ldp lsp output matches 2\.2\.2\.2/32.
Stuck? Ask the coach
Tell the coach what you see or what you tried. It gives you a hint, not the answer, the way a senior engineer would. Included with a free trial or any plan.
Ask the coach
Reference solution
Try it yourself first — the lab checks your work either way. This is one configuration that makes every task pass, device by device:
B system-view
interface GigabitEthernet0/0/0
mpls ldp
quit
return
Related labs
Where to start
The lessons are open to everyone, all guided labs are listed by track, and
plans explains what is free and what is not.
CCNA®, CCNP® and Cisco® are trademarks of Cisco Systems, Inc. zNetLaB is not affiliated with or endorsed by Cisco.
Try the simulator in your browser, no sign-up