zNetLaB › Guided labs › Enterprise
SD-WAN fabric from controllers to a service VPN
Enterprise Advanced 8 devices 5 checked tasks 100 points Plan lab
vBond, vSmart and vManage sit on a routed transport with two cEdges. Bring up the control plane, the BFD session between the edges and VPN 10 so the two branch routers reach each other without the transport learning either LAN. You build it in a browser, type real commands at each device, and every task below is
checked against the running configuration — so you find out it is wrong before anybody else does.
Open this lab in the simulator
The simulator runs in your browser with nothing to install. This lab is part of the full simulator: open it free for 7 days with a new account, then with a plan. It needs an account, which keeps your progress.
The scenario
vBond, vSmart and vManage sit on a routed transport with two cEdges. Bring up the control plane, the BFD session between the edges and VPN 10 so the two branch routers reach each other without the transport learning either LAN.
Your role: a network engineer on the enterprise team. Level: Advanced Done when: all 5 goals show as passed (100 points).
Network status
Devices: 1 switch, 7 routers, cabled as drawn. No Layer 1 or Layer 2 faults: every link is connected and up. WAN, VB, VS, VM, E1, E2, R1, R2 start with an empty configuration.
Known problems
None: nothing is misconfigured. The network is simply not finished: what the goals list is what you have to build or secure.
Goals
Edge 1 has a control connection up to vSmart (20 pts) BFD is up between the edges (20 pts) Edge 1 has the site 2 LAN as an OMP route in VPN 10 (20 pts) R1 reaches R2 across the overlay (25 pts) The transport never learns a branch LAN (15 pts)
The activity, in order
Edge 1 has a control connection up to vSmart Route the transport on WAN. On each controller: system-ip, site-id 100, organization-name ORG, vbond 10.0.1.2 (local on the vBond), and VPN 0 with its address and default route; commit. On each edge: the same organisation and vBond, its own system-ip and site-id, and a tunnel-interface with color mpls on GigabitEthernet0/0/0.Why: Each goal is a state the lab can check on the running device. Verify with: show sdwan control connections BFD is up between the edges Each edge learns the other one TLOC from vSmart through OMP and runs BFD to it.Why: Each goal is a state the lab can check on the running device. Verify with: show sdwan bfd sessions Edge 1 has the site 2 LAN as an OMP route in VPN 10 Put GigabitEthernet0/0/1 in vpn 10 under sdwan on both edges.Why: Each goal is a state the lab can check on the running device. Verify with: show sdwan omp routes R1 reaches R2 across the overlay Address the branch routers and point their default at the edge.Why: Each goal is a state the lab can check on the running device. Verify with: ping 192.168.2.5 The transport never learns a branch LAN Nothing to configure: VPN 10 travels inside the tunnels.Why: Each goal is a state the lab can check on the running device. Verify with: show ip route
Tips
Work in the order given: later goals depend on the earlier ones. After every change, run the verify command before moving on; do not guess. Stuck? Read the verify output first. It names the interface, neighbour or route that is wrong.
Why this matters
vBond, vSmart and vManage sit on a routed transport with two cEdges. Bring up the control plane, the BFD session between the edges and VPN 10 so the two branch routers reach each other without the transport learning either LAN.
What you will be able to do
Edge 1 has a control connection up to vSmart
BFD is up between the edges
Edge 1 has the site 2 LAN as an OMP route in VPN 10
R1 reaches R2 across the overlay
The network
Catalyst 9300-24, vBond, vSmart, vManage, cEdge ISR 1100-4G, Catalyst 8000V — 8 devices in all, already cabled.
Gi1/0/1 ge0/0 Gi1/0/2 eth0 Gi1/0/3 eth0 Gi1/0/4 Gi0/0/0 Gi1/0/5 Gi0/0/0 Gi1 Gi0/0/1 Gi1 Gi0/0/1 WAN VB VS VM E1 E2 R1 R2 Drawn from this lab: devices, cables, ports and the addresses already set.
Device Model Address already set
WAN Catalyst 9300-24 configure it
VB vBond configure it
VS vSmart configure it
VM vManage configure it
E1 cEdge ISR 1100-4G configure it
E2 cEdge ISR 1100-4G configure it
R1 Catalyst 8000V configure it
R2 Catalyst 8000V configure it
Cabling
WAN Gi1/0/1 ↔ VB ge0/0
WAN Gi1/0/2 ↔ VS eth0
WAN Gi1/0/3 ↔ VM eth0
WAN Gi1/0/4 ↔ E1 Gi0/0/0
WAN Gi1/0/5 ↔ E2 Gi0/0/0
R1 Gi1 ↔ E1 Gi0/0/1
R2 Gi1 ↔ E2 Gi0/0/1
What is configured at the start
Nothing is configured to start with beyond the addresses above: you build the configuration from a clean start.
Tasks, and how each one is checked
Every task is decided by reading the live network — a neighbour in FULL, a ping that succeeds, a line in the running configuration — not by looking for a keyword you typed. The same command shows you what the lab sees.
# Task Pts How to verify it yourself
1 Edge 1 has a control connection up to vSmart 20 On E1: show sdwan control connections output matches vsmart\s+dtls\s+1\.1\.1\.2[\s\S]*?up.
2 BFD is up between the edges 20 On E1: show sdwan bfd sessions output matches 2\.2\.2\.2[\s\S]*up.
3 Edge 1 has the site 2 LAN as an OMP route in VPN 10 20 On E1: show sdwan omp routes output matches 10\s+192\.168\.2\.0.
4 R1 reaches R2 across the overlay 25 On R1: ping 192.168.2.5 must succeed.
5 The transport never learns a branch LAN 15 On E1: show sdwan omp routes output matches 192\.168\.2\.0. and On WAN: show ip route does not list 192.168.2.0/24.
Stuck? Ask the coach
Tell the coach what you see or what you tried. It gives you a hint, not the answer, the way a senior engineer would. Included with a free trial or any plan.
Ask the coach
Reference solution
Try it yourself first — the lab checks your work either way. This is one configuration that makes every task pass, device by device:
WAN ip routing
interface GigabitEthernet1/0/1
no switchport
ip address 10.0.1.1 255.255.255.0
no shutdown
exit
interface GigabitEthernet1/0/2
no switchport
ip address 10.0.2.1 255.255.255.0
no shutdown
exit
interface GigabitEthernet1/0/3
no switchport
ip address 10.0.3.1 255.255.255.0
no shutdown
exit
interface GigabitEthernet1/0/4
no switchport
ip address 10.0.4.1 255.255.255.0
no shutdown
exit
interface GigabitEthernet1/0/5
no switchport
ip address 10.0.5.1 255.255.255.0
no shutdown
exit
VB config
system
system-ip 1.1.1.1
site-id 100
organization-name ORG
vbond 10.0.1.2 local
exit
vpn 0
interface ge0/0
ip address 10.0.1.2/24
no shutdown
exit
ip route 0.0.0.0/0 10.0.1.1
commit and-quit
VS config
system
system-ip 1.1.1.2
site-id 100
organization-name ORG
vbond 10.0.1.2
exit
vpn 0
interface eth0
ip address 10.0.2.2/24
no shutdown
exit
ip route 0.0.0.0/0 10.0.2.1
commit and-quit
VM config
system
system-ip 1.1.1.3
site-id 100
organization-name ORG
vbond 10.0.1.2
exit
vpn 0
interface eth0
ip address 10.0.3.2/24
no shutdown
exit
ip route 0.0.0.0/0 10.0.3.1
commit and-quit
E1 interface GigabitEthernet0/0/0
ip address 10.0.4.2 255.255.255.0
no shutdown
exit
interface GigabitEthernet0/0/1
ip address 192.168.1.1 255.255.255.0
no shutdown
exit
ip route 0.0.0.0 0.0.0.0 10.0.4.1
system
system-ip 2.2.2.1
site-id 1
organization-name ORG
vbond 10.0.1.2
exit
sdwan
interface GigabitEthernet0/0/0
tunnel-interface
color mpls
encapsulation ipsec
exit
vpn 10
interface GigabitEthernet0/0/1
exit
exit
E2 interface GigabitEthernet0/0/0
ip address 10.0.5.2 255.255.255.0
no shutdown
exit
interface GigabitEthernet0/0/1
ip address 192.168.2.1 255.255.255.0
no shutdown
exit
ip route 0.0.0.0 0.0.0.0 10.0.5.1
system
system-ip 2.2.2.2
site-id 2
organization-name ORG
vbond 10.0.1.2
exit
sdwan
interface GigabitEthernet0/0/0
tunnel-interface
color mpls
encapsulation ipsec
exit
vpn 10
interface GigabitEthernet0/0/1
exit
exit
R1 interface GigabitEthernet1
ip address 192.168.1.5 255.255.255.0
no shutdown
exit
ip route 0.0.0.0 0.0.0.0 192.168.1.1
R2 interface GigabitEthernet1
ip address 192.168.2.5 255.255.255.0
no shutdown
exit
ip route 0.0.0.0 0.0.0.0 192.168.2.1
Related labs
Where to start
The lessons are open to everyone, all guided labs are listed by track, and
plans explains what is free and what is not.
CCNA®, CCNP® and Cisco® are trademarks of Cisco Systems, Inc. zNetLaB is not affiliated with or endorsed by Cisco.
Try the simulator in your browser, no sign-up