zNetLaB › Guided labs › Service Provider
OSPFv3 across Junos, Arista EOS and IOS XR
Service Provider Advanced 3 devices 4 checked tasks 100 points Plan lab
A vMX, a vEOS router and an ASR 9001 in a row, IPv6 on both links. Run OSPFv3 area 0 on all three so the vMX reaches the far end of the XR link. You build it in a browser, type real commands at each device, and every task below is
checked against the running configuration — so you find out it is wrong before anybody else does.
Open this lab in the simulator
The simulator runs in your browser with nothing to install. This lab is part of the full simulator: open it free for 7 days with a new account, then with a plan. It needs an account, which keeps your progress.
The scenario
A vMX, a vEOS router and an ASR 9001 in a row, IPv6 on both links. Run OSPFv3 area 0 on all three so the vMX reaches the far end of the XR link.
Your role: an engineer in the provider’s network operations centre. Level: Advanced Done when: all 4 goals show as passed (100 points).
Network status
Devices: 3 routers, cabled as drawn. No Layer 1 or Layer 2 faults: every link is connected and up. J, E, X start with an empty configuration.
Known problems
None: nothing is misconfigured. The network is simply not finished: what the goals list is what you have to build or secure.
Goals
J is Full with E (25 pts) X is FULL with E (25 pts) J learns the E to X link (25 pts) J reaches X over IPv6 (25 pts)
The activity, in order
J is Full with E J: inet6 address 2001:db8:1::1/64 on ge-0/0/0.0, routing-options router-id 1.1.1.1, protocols ospf3 area 0.0.0.0 interface ge-0/0/0.0. E: ip routing and ipv6 unicast-routing, both ports routed with an IPv6 address and ospfv3 area 0.0.0.0, router ospfv3 with router-id 2.2.2.2.Why: Each goal is a state the lab can check on the running device. Verify with: show ospf3 neighbor X is FULL with E X: 2001:db8:2::3/64 on GigabitEthernet0/0/0/0 (and an IPv4 address), router ospfv3 1 with router-id 3.3.3.3 and the interface in area 0; commit.Why: Each goal is a state the lab can check on the running device. Verify with: show ospfv3 neighbor J learns the E to X link E carries the second link into area 0, so J learns it as an OSPF route.Why: Each goal is a state the lab can check on the running device. Verify with: show route table inet6.0 J reaches X over IPv6 With routes both ways the ping crosses E.Why: Each goal is a state the lab can check on the running device. Verify with: ping 2001:db8:2::3 count 3
Tips
Work in the order given: later goals depend on the earlier ones. After every change, run the verify command before moving on; do not guess. Stuck? Read the verify output first. It names the interface, neighbour or route that is wrong.
Why this matters
A vMX, a vEOS router and an ASR 9001 in a row, IPv6 on both links. Run OSPFv3 area 0 on all three so the vMX reaches the far end of the XR link.
What you will be able to do
J is Full with E
X is FULL with E
J learns the E to X link
J reaches X over IPv6
The network
vMX, Arista vEOS Router, ASR 9001 — 3 devices in all, already cabled.
ge-0/0/0 Eth1 Eth2 Gi0/0/0/0 J E X Drawn from this lab: devices, cables, ports and the addresses already set.
Device Model Address already set
J vMX configure it
E Arista vEOS Router configure it
X ASR 9001 configure it
Cabling
J ge-0/0/0 ↔ E Ethernet1
E Ethernet2 ↔ X Gi0/0/0/0
What is configured at the start
Nothing is configured to start with beyond the addresses above: you build the configuration from a clean start.
Tasks, and how each one is checked
Every task is decided by reading the live network — a neighbour in FULL, a ping that succeeds, a line in the running configuration — not by looking for a keyword you typed. The same command shows you what the lab sees.
# Task Pts How to verify it yourself
1 J is Full with E 25 On J: show ospf3 neighbor output matches 2\.2\.2\.2\s+ge-0/0/0\S*\s+Full.
2 X is FULL with E 25 On X: show ospfv3 neighbor output matches 2\.2\.2\.2\s+\d+\s+FULL.
3 J learns the E to X link 25 On J: show route table inet6.0 output matches 2001:db8:2::/64.
4 J reaches X over IPv6 25 On J: ping 2001:db8:2::3 count 3 output matches 0\.0% packet loss.
Stuck? Ask the coach
Tell the coach what you see or what you tried. It gives you a hint, not the answer, the way a senior engineer would. Included with a free trial or any plan.
Ask the coach
Reference solution
Try it yourself first — the lab checks your work either way. This is one configuration that makes every task pass, device by device:
J configure
set interfaces ge-0/0/0 unit 0 family inet6 address 2001:db8:1::1/64
set routing-options router-id 1.1.1.1
set protocols ospf3 area 0.0.0.0 interface ge-0/0/0.0
commit
exit
E ip routing
ipv6 unicast-routing
interface Ethernet1
no switchport
ipv6 address 2001:db8:1::2/64
ospfv3 area 0.0.0.0
exit
interface Ethernet2
no switchport
ipv6 address 2001:db8:2::2/64
ospfv3 area 0.0.0.0
exit
router ospfv3
router-id 2.2.2.2
exit
X configure
interface GigabitEthernet0/0/0/0
ipv4 address 10.0.23.3 255.255.255.0
ipv6 address 2001:db8:2::3/64
no shutdown
exit
router ospfv3 1
router-id 3.3.3.3
area 0
interface GigabitEthernet0/0/0/0
exit
exit
exit
commit
Related labs
Where to start
The lessons are open to everyone, all guided labs are listed by track, and
plans explains what is free and what is not.
CCNA®, CCNP® and Cisco® are trademarks of Cisco Systems, Inc. zNetLaB is not affiliated with or endorsed by Cisco.
Try the simulator in your browser, no sign-up